ASTM D – 11, “Standard Test Methods for Field Measurement of Surface locations and the arithmetic mean determined, Method C—A composite plastic. Designation: D – 03Standard Test Methods for Field Measurement of 3 Method C—A composite plastic tape is impressed into Method C—A These test methods are under the jurisdiction of ASTM Committee D01 on The sole. ASTM D – 11 Standard Test Methods for Field Measurement of Surface Profile 1 of 8 standard.3 Method C—A special tape3 containing a compressible 6.

Author: Arajas Jushakar
Country: Lebanon
Language: English (Spanish)
Genre: Sex
Published (Last): 26 September 2014
Pages: 25
PDF File Size: 15.18 Mb
ePub File Size: 17.26 Mb
ISBN: 921-5-31848-682-1
Downloads: 68422
Price: Free* [*Free Regsitration Required]
Uploader: Akigami

It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices c4417 determine the applicability of regulatory limitations prior to use.

Difference in Surface Profile Measurements: ASTM D Method B vs CKTA University

Since corrosion products expand as they migrate beneath a coating film, the coating may disbond, leaving the substrate unprotected. This is done because of evidence that coatings performance in any one small area is primarily astm d4417 method c by the highest surface features in that area and not astm d4417 method c the average roughness.

This method can be used to measure the surface profile depth that is created by abrasive blast cleaning or impact-type power tools. Naturally, the ability to generate reliable data between users employing different instruments, as well as the ability of one user to generate repeatable data using a single instrument, must be assessed. The instruments described are readily portable and sufficiently sturdy for use in the field. For example, requiring a 5.

There are additional techniques suitable for laboratory use not covered by these test methods.

Coatings specialists may use the atsm for evaluating the adhesion characteristics of an existing coating during a coating condition survey, or in a failure investigation.

Specify the Test Instrument!

Standards for Measurement of Surface Profile There are currently four primary standards for measurement of surface profile in steel surfaces. Information relating to testing the tensile f strength of coatings applied to surfaces astm d4417 method c than steel will be removed from D during revisions that are also planned for Therefore, differences are inevitable, particularly with deeper surface profiles, and astm d4417 method c results may or may not fall within the specified range for one of the two methods.

For this reason, astm d4417 method c profile should be measured prior to coating application to ensure that it meets that specified. Leave a Reply Cancel reply Your email address will satm be published. As a result, a major revision to the standard was initiated in and continues today.

Without reliable methods for extracting a sample from astm d4417 method c surface and analysis of the collected sample, the degree and type of surface cleaning required prior to coating installation can be uncertain.

Generally, if it was not addressed in the specification, then scoring was not astm d4417 method c be done. Same Surface, Different Results? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. However, thick film coatings i. The method describes three different procedures for quantifying surface profile, including visual comparators Method Adepth micrometers Method B and replica tape Method C.

Industrial Protective Coatings

The subcommittee develops and maintains standard test methods, practices and guides relating to astm d4417 method c performance, evaluation, specification, application and proper use of industrial protective coatings. This movement may be caused by expansion and contraction of the substrate due to temperature fluctuation, or live loads placed onto a structure; for example, traffic crossing a bridge.

Surface Chloride Extraction and Analysis The protective coatings industry has long recognized the potential consequences of coating over soluble salts i. Coarse replica tape is used astm d4417 method c measure the actual roughness of surfaces containing a profile from 0.

In response to a growing demand, a number of coatings were developed and advertised as being resistant to graffiti, or easily cleaned of graffiti. During abrasive blast cleaning, the mass of the abrasive and the velocity of the abrasive movement created by astm d4417 method c air generates kinetic energy the abrasive can reach speeds of over miles per hour as it exits v4417 blast nozzle.

Total of seven possible cleaning materials rather than five.

Differences in Surface Profile Measurements: ASTM D4417- Method B vs. Method C

Historical Version s – view previous versions of standard Work Item s – proposed revisions of this standard Translated Astm d4417 method c s: The pull-off method is widely used by coatings manufacturers, specifiers, inspectors and astm d4417 method c specialists.

References 1 Roper, Hugh J. The results of the interlaboratory study and the content of the research report will be reviewed in early This method encompasses only one surface characteristic: Coating manufacturers may also consider these requirements to improve the performance and the service life of the coatings they supply. Models from a few gage manufacturers are available that conform to this standard.

This can be discussed and agreed upon at the pre-construction conference. He has been employed by KTA for over 27 years.

Today, Method B and Method C are the adtm commonly used, astm d4417 method c that is what we will astm d4417 method c focusing on. Recently published articles 1 describe the importance of other surface roughness x, in addition to average peak-to-valley distance, including peak count P cmaximum roughness depth R max and maximum profile height R t.

The entire standard is being revised, and will include among other changes more specific operating procedures for the various types of test equipment.